Shock Absorber replacement parts for 2008 KTM 690 Enduro 9703H6 (EU)

OEM Parts Ktm 2008 Ktm 690 Enduro Shock Absorber

SHOCK ABSORBER Full screen diagram

Please note: If a part is displayed on the diagram but not shown in the parts list, it is no longer available.

Location	Part Description

1	MONOSHOCK 690 ENDURO 08 Part #: 15187D11 Required per assembly: 1 Not Available
2	SHOCK ABS. UPPER CPL. 08 Part #: 46180682S1 Required per assembly: 1 Not Available
3	LOCK RING D=55 Part #: 46180519 Required per assembly: 1 Special order item. Not Available View to order
4	MEMBRANE COVER CPL. 08 Part #: 46180661S Required per assembly: 1 Not Available
5	MEMBRANE D52 Part #: 46180518 Required per assembly: 1 Special order item. Not Available View to order
6	HS CYLINDER-HEAD SCREW R1/8 L8 Part #: 50180095 Required per assembly: 1 $2.85 $2.42 - + Add to cart
7	CYL., SCREW, M10X1, 25, L=53 Part #: 76504016000 Required per assembly: 2 $4.99 $4.24 - + Add to cart
10	COMPRESSION CPL. Part #: 46180533S1 Required per assembly: 1 $478.05 $385.50 - + Add to cart
11	ROUND-WIRE, SNAP, RING, 49X1, 5 Part #: 46810010 Required per assembly: 1 $3.62 $3.08 - + Add to cart
20	SHOCK ABS BOTTOM CPL. ENDURO Part #: 46180654S1 Required per assembly: 1 $826.49 $666.48 - + Add to cart
21	REPAIR KIT BEARINGS 07 Part #: R15006 Required per assembly: 1 $121.26 $95.37 - + Add to cart
30	COUNTERNUT Part #: 46180445 Required per assembly: 1 Not Available
31	ADJUSTING NUT Part #: 46180444 Required per assembly: 1 Not Available
32	SPRING 220MM 75N/MM (61) Part #: 91110003S $177.53 $150.90 - + Add to cart
32	SPRING 220MM 85N/MM (61) Part #: 91110005S $183.03 $155.58 - + Add to cart
32	SPRING 220MM 80N/MM (61) Part #: 91110004S $177.53 $150.90 - + Add to cart
33	SPRING RETAINER 28X73X15 BLACK Part #: 46181299 Required per assembly: 1 $72.26 $61.42 - + Add to cart
40	REPAIR KIT GASKET 05 Part #: R15004T Required per assembly: 1 $69.29 $58.90 - + Add to cart
41	SHOCK ABSORBER FLUID 5 LT Part #: 50180751S1 Required per assembly: 1 $175.99 $149.59 - + Add to cart

Other assembly diagrams for this model

AIR FILTER

BALANCER SHAFT

BATTERY

CLUTCH

CLUTCH COVER

COOLING SYSTEM

CRANKSHAFT, PISTON

CYLINDER

CYLINDER HEAD

DECAL

ELECTRIC STARTER

ENGINE CASE

ENGINE GUARD

EXHAUST SYSTEM

FRAME

FRONT BRAKE CALIPER

FRONT BRAKE CONTROL

FRONT FORK DISASSEMBLED

FRONT FORK, TRIPLE CLAMP

FRONT WHEEL

FUEL PUMP

HANDLEBAR, CONTROLS

IGNITION SYSTEM

INSTRUMENTS / LOCK SYSTEM

LIGHTING SYSTEM

LUBRICATING SYSTEM

MASK, FENDERS

PRO LEVER LINKING

REAR BRAKE CALIPER

REAR BRAKE CONTROL

REAR WHEEL

SECONDARY AIR SYSTEM SAS

SEPERATE ENCLOSURE

SHIFTING MECHANISM

SHOCK ABSORBER

SIDE / CENTER STAND

SPECIAL TOOLS

Special tools (engine)

SWING ARM

TANK, SEAT

THROTTLE BODY

TIMING DRIVE

TRANSMISSION I - MAIN SHAFT

TRANSMISSION II - COUNTERSHAFT

VALVE DRIVE

WATER PUMP

WIRING HARNESS

WP SHIMS FOR SETTING

Back to top