Exhaust System replacement parts for 2011 KTM 125 Duke 8003K4 (EU)

OEM Parts Ktm 2011 Ktm 125 Duke Exhaust System

EXHAUST SYSTEM Full screen diagram

Please note: If a part is displayed on the diagram but not shown in the parts list, it is no longer available.

Location	Part Description

1	SILENCER CPL. Part #: 90105083000 Required per assembly: 1 Not Available
2	EXHAUST PIPE A CPL. Part #: 90105007033 Required per assembly: 1 Not Available
3	HEAT SHIELD CPL. Part #: 90105090033 Required per assembly: 1 ~~$38.82~~ $33.00 - + Add to cart
4	EXHAUST FLANGE GASKET Part #: 90105004000 Required per assembly: 1 $7.57 - + Add to cart
5	OXYGEN SENSOR Part #: 90141090000 Required per assembly: 1 ~~$232.38~~ $228.39 - + Add to cart
6	CLAMP CPL. Part #: 90105051000 Required per assembly: 1 Not Available
7	SEAL RING EXHAUST PIPE A Part #: 90105005000 Required per assembly: 1 Not Available
8	MUFFLER MOUNTING TUBE Part #: 90105084000 Required per assembly: 1 $5.93 - + Add to cart
9	DAMPING ELEMENT Part #: 90105068000 Required per assembly: 4 Note: ONLY FOR OLD SILENCER VERSION Not Available
10	FLANGED NUT M10X1.25 WS14 Part #: 90103038002 Required per assembly: 1 $3.63 - + Add to cart
11	HH COLLAR SCREW M8X110 SW12 Part #: J027081103 Required per assembly: 1 $4.79 - + Add to cart
12	CLIP NUT Part #: 90103097000 Required per assembly: 2 $5.93 - + Add to cart
13	RUBBER CAP Part #: 90105085000 Required per assembly: 2 $3.63 - + Add to cart
14	HH COLLAR SCREW M6X14 SW10 Part #: J025060146 Required per assembly: 2 $2.44 - + Add to cart
15	HH COLLAR SCREW M6X25 SW10 Part #: J025060256 Required per assembly: 2 $2.44 - + Add to cart
16	COLLAR BUSHING Part #: 90105069000 Required per assembly: 4 Note: ONLY FOR OLD SILENCER VERSION Not Available
17	DAMPING ELEMENT UPPER Part #: 90105068200 Required per assembly: 2 Note: ONLY FOR NEW SILENCER VERSION $2.44 - + Add to cart
18	COLLAR BUSH Part #: 90105069100 Required per assembly: 4 Note: ONLY FOR NEW SILENCER VERSION $5.93 - + Add to cart
19	DAMPER, BOTTOM Part #: 90105068100 Required per assembly: 2 Note: ONLY FOR NEW SILENCER VERSION $2.44 - + Add to cart

Other assembly diagrams for this model

AIR FILTER

BALANCER SHAFT

CLUTCH

CLUTCH COVER

COOLING SYSTEM

CRANKSHAFT, PISTON

CYLINDER

CYLINDER HEAD

DECAL

DIAGNOSTIC TOOL

ELECTRIC STARTER

ENGINE CASE

EXHAUST SYSTEM

FRAME

FRONT BRAKE CALIPER

FRONT FORK, TRIPLE CLAMP

FRONT WHEEL

FUEL PUMP

HANDLEBAR, CONTROLS

IGNITION SYSTEM

INSTRUMENTS / LOCK SYSTEM

LIGHTING SYSTEM

LUBRICATING SYSTEM

MASK, FENDERS

REAR BRAKE CALIPER

REAR WHEEL

SEPERATE ENCLOSURE

SHIFTING MECHANISM

SHOCK ABSORBER

SIDE / CENTER STAND

SWING ARM

TANK, SEAT

THROTTLE BODY

TIMING DRIVE

TRANSMISSION I - MAIN SHAFT

TRANSMISSION II - COUNTERSHAFT

VALVE DRIVE

WATER PUMP

WIRING HARNESS

Back to top